Sony RM-VL600T Manuale Utente

3-284-974-12 (1)IntegratedRemoteCommander© 2007 Sony CorporationRM-VL600TOperating Instructions

10Setting a Component Code bythe Search FunctionYou can find a code number available for acomponent that does not have one in the supplied“Component c

11Operating Your Componentswith the Remote CommanderWhen you operate a non-Sony component, makesure you set the component code first (page 8).SETSATDV

12Programming Signals of AnotherRemote Control — LearningFunctionTo operate components or functions which do notwork even if you set a component code

13Example: To programme the N (Play) signal ofyour video cassette recorder to the VCR N(Play) button of the Commander1 Place the RM-VL600T head to hea

14If the SET indicator flashes five timesIt means that “learning” is incomplete. Repeat steps 4and 5.6 Repeat Steps 4 and 5 to “teach” functionsto oth

15Programming remote control signals tothe Component Select buttons andSystem Control buttonsYou can “teach” one operating procedure to aComponent Sel

16Changing or erasing the function of a“learned” buttonTo change the “learned” function, clear it first andperform Learning again.To clear the “learne

17To erase the learned function of the ComponentSelect button and System Control buttonsExample: To erase the function “learned” by theTV button1 Whil

18Notes on programming the signals for anair-conditionerAbout seasonal adjustmentsIf you change the settings of the air-conditioner forthe season, you

19Advanced FeaturesControlling the Volume of VisualComponents Connected to anAudio SystemThe Commander is factory preset based on theassumption that y

2FeaturesThe RM-VL600T Remote Commander providescentralised control of all your AV componentsfrom a single remote commander and saves thetrouble of op

20SATDVDTV CBLTAPECDVCR AMPSATDVDTV CBLTAPECDVCR AMPVolume control setting complete.To set only the audio components’ volumecontrols to AMPPress 2 – w

21SETSATDVDTV CBLTAPECDVCR1VIDEO12VIDEO23AUX4TUNER5CD6TA PE7MD8TV9PHONO0DVDGUIDE MENUTOOLSSYSTEM CONTROLAMPENTOKABCD1-/--RETURNANALOGDIGITALPROGRAM1 2

22Example: To programme the procedure above tothe SYSTEM CONTROL B button1 Press and while holding SET, press theSYSTEM CONTROL B button.The SET indic

23Programming a Series ofCommands on the ComponentSelect ButtonsAs with the SYSTEM CONTROL buttons, you canalso programme a series of operating comman

24To clear programmed commands1 Press and while holding SET, press andhold for more than 3 seconds theComponent Select button you want toclear.Notes•Y

251 Press and while holding 1, press t andPROGRAM +.1PROGRAM++The SET indicator and the Component Selectbutton currently selected flash once, and theH

26Erasing All Settings— To reset the Commander toits factory settingsYou can erase all remote control signalsprogrammed by the “learned“ function to r

27Additional InformationPrecautions•Do not drop the unit or give a shock to the unit, orit may cause a malfunction.•Do not leave the unit in a locatio

28TroubleshootingIf you have problems setting up or using the Remote Commander, first check the batteries (page 6), thencheck the items below.Remedy•

29SymptomAll Component Select buttons flash twice.After programming the Power-On command of acomponent, pressing that Component Select button doesnot

Startup GuideThis guide shows you how to set the Remote Commander to operate your components.First, find the four-digit component code number for your

30KEY DISPLAY0112qs1 – 9, 0, ENT, -,1 –, 2 –qat (INPUTSELECT)qjMENUqk Vqk vqk bqk Bqk OKqfPROGRAM +/–TV(ANALOGUE)FUNCTIONTo turn on and off.To change

31KEY DISPLAY019RED (m), GREEN(N), YELLOW (M),BLUE (x)1 21 – 9, 0, -/--qa t(INPUT SELECT)7GUIDE8RETURN (EXIT)qg /(TELETEXT)qjMENUqlTOOLS (EPG)qk Vqk

32Using FastextWith Fastext you can access pages with one keystroke.When a Fastext page is broadcast, a colour-codedmenu will appear at the bottom of

33KEY DISPLAY019m9N9M9REC z9x9X11 – 9, 0qsENTqfPROGRAM + (>)qfPROGRAM – (.)DATFUNCTIONTo turn on and off.To rewind.To play.To fast-forward.To recor

34IndexA, BBatteries 6C, DChanging 16Clearing/Changinglearned signal 16, 17Power-On command 20Code numbers 8, 10Component Select buttonsassigning

Printed in China

1 Place the RM-VL600T head to head withyour VCR’s remote control.2 Set the RM-VL600T for “learning” mode.Press and hold SET for at least 3 secondsunti

5Table of ContentsStartup Guide ... 3Getting StartedInstalling the Batteries ...

6Getting StartedInstalling the BatteriesSlide open the battery compartment lid and inserttwo R6 (size AA) batteries. Be sure to match up the+ and – in

7Location of ControlsAbout tactile dotsThe number 5 button, the N button and PROGRAM + button each have a tactile dot for ease of use.* Note on the 2

8Example: To set up a Philips’ TV1 See the tables in the supplied “Componentcode numbers,” and find the four-digitcomponent code number for the desire

9Notes• If you press a component code number that is not on thetable in the supplied “Component code numbers,” or ifyou press a button in the wrong or